Description

The T3000 Restorers Moisture Detection Starter Kit is an essential tool for every restorer to conduct moisture analysis in a multitude of situations.

The brain of the kit is the T3000 Multifunction meter which can replace a tool box full of individual meters when coupled with the available sensors.  The T3000 has data recording capabilities and when coupled with the software data can be downloaded allowing you to manage and evaluate your projects.

Also included is a professional infrared thermometer with multi-point laser technology (TP7)

Sensors/probes included in this kit are: 

• Dielectric material moisture sensor (TS 660 SDI) allowing near-surface moisture measurement up to 4 cm

• Hygrometer (TS 210 SD) to check if conditions are optimal for your dehumidifiers and heat drying equipment

• Hand electrode (TS 60) with non-insulated electrodes multi-pack

• Hammer probe (TS 070) with 10 insulated pins (TS 070)

• Insulated rods (TS 012/300) x 2

• Insulated paddles(TS 016/300) x 2

• Compound to promote better conductivity and more accurate measurements
  

More information can be found on any of the above by clicking on the individual products links.

The kit

The Restore Solutions Starter Restorers Moisture Detection Kit includes: 

T3000 Multifunction Measuring Meter

The T3000 is the brain of the operation and assists with logging, reporting and works with lots of different accessories.

TS 210 SDI Climate Sensor

The starter kit comes with a hygrometer. This is going to be helpful, especially if you’re doing heat drying or if you’re working with dehumidification.

You want to know what air is coming in and what air is coming out of your dehumidifier. It is a fantastic, good quality hydrometer.

TS 660 SDI Material Moisture Sensor

It comes with our wall diametric wall meter. This meter can go into 40 mm of concrete, it can go through two layers of tiles, it works with timber, walls, flooring, and many other things. 

This hygrometer is very easy to use.

TP 7 Infrared Temperature Gun

Our basic kit also includes a temperature gun. An infrared temperature gun is going to be able to detect the surface temperature of your materials.

This is handy when you’re raising the surface temperature of those materials to get faster drying.

TS 060 Hand Electrode

We also include a hand-held pin probe with non-insulated pins included. We have a lot of different sizes and you can connect them into the top and run a cable from there to the actual T3000 and then you’ve got a pin meter to check, from timber to walls through to carpet.

TS 070 Ram-In Electrode

We also include a good quality hammer probe. Start hammer probing into framing or into your timber floors.

With other kits, you often only get a couple of different pins. This kit comes with 10 insulated pins. They are fantastic 60ml long pins and 10 of them are included.

Trotec Silicone Protective Cover for T3000

The new silicone case protects valuable Trotec T3000 multifunction measuring device.

TS 016/300 Flat Electrodes, pair, insulated

Adapter TS 060 on round or flat electrode

TS 012/300 Round Electrodes, pair, 4 mm, insulated

TC 20 Connecting Cable, BNC

TC 30 Connecting Cable, SDI Sensors

Replacement Electrode Tips Can

TS 070 Electrode Tips, 60 mm, Teflon insulated

Contact Mass for TS 004 / TS 024

Transport Case II MultiMeasure Series T3000

Accessories

Add any of these accessories to make your kit even more powerful:

• TROTEC SILICONE PROTECTIVE COVER FOR T3000

• TROTEC HOLSTER 3 MULTIMEASURE-SERIES

• TROTEC CONTACT MASS

• TROTEC TS 070 ELECTRODE TIPS, 60 MM

• TROTEC REPLACEMENT ELECTRODE TIPS CAN

• TROTEC TEST BLOCK V1 FOR T510 / T3000

• TROTEC SURFACE TEMPERATURE SENSOR TS 131 SDI

• TS 250 SDI CLIMATE SENSOR

• MICROWAVE HUMIDITY SENSOR TS 610 SDI

• TS 020/110 BRUSH ELECTRODES, pair, insulated

• TS 004/300 ROUND ELECTRODES, PAIR, 2 MM

• TS 12/600 ROUND ELECTRODES

• Trotec T3000 Extension Handle

 
Downloads

• Practical handbook for multifunction measuring meter T3000 (EN)

• Wood Species Correction Data and Moisture Content

Software

Download the free version of the software from the Trotec website: MultiMeasure Studio analysis software 2.0 - 607 KB

*Please note when installing the software the first screen is in German and it is asking you to agree to the terms which are just standard Microsoft terms and conditions allowing the Trotec software the run.
The left hand hand button "ich stimme zu" is I agree and "ich stimme nicht zu" is I don't agree, you must select "ich stimme zu" to proceed with installing the software.

Or purchase the pro version here MultiMeasure Studio Professional 

FIND YOUR TROTEC STOCKIST HERE.